Warewashing Single rinse Rack Type dishwasher, 100 racks/hour, electric (COD 534410)
Where to buy
Single Rinse Rack Type dishwashers - 100 racks per hour

Warewashing
Single rinse Rack Type dishwasher, 100 racks/hour, electric

COD 534410

Single Rinse Rack Type Dishwasher, 100 racks/hour, electric, touch screen, insulated doors, customized direction on-site, 60Hz

Specifications

  • Supply voltage: 380-415 V/3N ph/60 Hz

    Default Installed Power: 25.2 kW

    Boiler heating elements: 12 kW

    Wash pump size: 1.18 kW

    Wash tank heating elements: 12 kW

  • Flow rate of wash pump: 400 l/min

    Inlet hot water line size: G 3/4"

    Inlet cold water line size:

    Drain line size: 50mm

    Inlet water supply pressure: 1.5-7 bar

    Inlet water supply temperature (wash and rinse): 50 - 65°C

    The higher the temperature, the faster the warm up. When there is ESD option installed, the machine should be connected to cold water up to 30°C.

    Inlet water supply hardness: 0 °fH / 0°dH

    When below 7°fH/4°dH special detergent and rinse aid are needed.

    Wash tank size: 70 l

  • Wash Temperature: 55 - 65 °C

    Productivity per hour (max speed): 100racks/1800dishes

    Final rinse temperature: 85 °C

    External dimensions, Width: 44 1/16" (1120 mm)

    External dimensions, Depth: 920 mm

    For transportation purpose only, the depth can be reduced to either 890mm by removing the main switch button or 792mm by removing the control box and the door handle.

    Height with door open: 2095 mm

    Charging hole size (width): 530 mm

    Charging hole size (height): 490 mm

    Shipping height: 1970 mm

    Shipping width: 1060 mm

    Shipping depth: 1260 mm

    Shipping volume: 2.63 m³

    Reference norm used to measure the noise: IEC60335-2-58 annex AA.

    Table to table distance: 1120 mm

  • Rinse water consumption at max speed (l/rack): 1.5 lt/rack

    Rinse water consumption at max. speed (l/h): 150 l/h

    Noise level: <62 dBA

  • Air flow (top, exit): 107 / 107 m³/h

    Air temperature: 45 - 45 °C

    Air humidity (top, exit): 100 / 100 % r.h.

    The data is measured at exhaust points at 25°C and 60% r.h. ambient conditions, 18°C inlet water temperature and refer only to the machine.

    Latent heat: 8800 W

    Sensible heat: 4500 W

    This model requires a ventilation hood. Please refer to the attached "Recommended Exhaust Hood Design"

Product Features

Adjustable feet for full access underneath the machine for cleaning.
IP25 protection against water jets, solid objects and small animals (larger than 6 mm).
Intuitive touch screen control panel features user-friendly display to easily operate the machine and to monitor machine status. Three different levels of interaction are available each show relevant messages and information to the operator, the general maintenance staff and the authorized service partners.
All internal components: wash and rinse arms, tank filters, curtains can be easily removed for cleaning.
Unit equipped with USB port making it simple to read data such as machine identification, counters and consumption, components, devices and alarm logs. Machine parameters can be uploaded and downloaded and firmware updated.
Maximum capacity per hour of 100 racks.
Large counter balanced inspection door allow unrestricted all-round access to the wash and rinse area. Door is insulated with injected foam. This adds strength as well as reduces noise and heat loss.
One conveyor speed can be selected through the control panel by the operator.
Deep drawn pressed wash tank with fully rounded corners, sloped towards the drain to prevent dirt buildup, provides fast drainage in just a few minutes. With no welding points the pressed tank offers a guaranteed water tight solution.
Dishwasher structure is held together with a solid 50 x 50 mm stainless steel frame to provide long-term sturdiness.
All electric components are put in one IP65 central box isolated from water and steam to ensure high reliability.
External pre-arrangement for inlet water, drain water, detergent & rinse aid connections for fast and easy installation on both sides of the unit.
All main components made in heavy duty anti-corrosive 304 type stainless steel: external front, side panels and internal chambers, wash and rinse arms, doors and rack transportation system.
The feeding direction is right to left as pre-arrangement from the factory, but it can be simply reversed on-site to left to right.
The unit is built on modularity concept for easy to add dryer module on-site.

Complete the form below to request more information

Select your country

 
Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

×